Recent Posts

Pages: [1] 2 3 ... 10
1
LF250 / skygo dragster 250 2011
« Last post by rhodesian on October 07, 2017, 08:52:32 AM »
need clutch kit and gaskets. any recomendations, in the uk  ;D
2
LF400 / LF400. Any Manual
« Last post by António Teles on July 13, 2017, 07:22:08 AM »
Hello Lifan drivers.
I have one LF400, but I don't know nothing about. Could you send to me a link where I can take information about mantenaince and others mecanic information. Send anything y haven't no information.
Hopping yours answers
Best regards
3
Chit Chat / Skygo SG400 by Lifan new portuguese member
« Last post by António Teles on July 13, 2017, 06:54:45 AM »
Hi,  I am glad to be here.
It's my first Lifan and Chopper, however I had others motorcycles and I ride maybe 350 000kms in Portugal and Spain.
I am going try help somebody and learn more about Lifan LF400 is the same motorcycle.
Atention my English isn't good enough, and I am not mecanic.
Nice ride for all
4
Engine Kits / Lifan clutch issue
« Last post by Papa nubby on June 08, 2017, 11:30:32 AM »
I have a lifan 125cc semi auto 3spd with reverse its on a go kart i recently bought. My question is why did i lose 3rd gear when i replaced the clutch.

Thanks for any help
5
Chit Chat / Lifan 125t 9l scooter speed
« Last post by Jjsp on May 26, 2017, 12:30:40 PM »
Please help, I've had my lifan now for some time but it won't go over 80kph/50mph. Is there anyway of getting it to go faster ?

It's only done 1200 kms and has had new plug, lead and carb clean.

I have read that because it's Chinese it's factory set to 50mph due to Chinese law.

There must be a way to get it to keep up with other scooters ?

Thanks guys
6
Chit Chat / Re: Lifan smoke screen.
« Last post by BaileySims on May 20, 2017, 12:51:10 PM »
Turns out that the piston I had first installed was indeed .5mm too small. I was able to get it to run correctly with the obvious correct sized piston. Now begins the fun part of building something to put this bad boy in.

https://youtu.be/ZMa-8aZ9wXk
7
Chit Chat / Re: Lifan smoke screen.
« Last post by BaileySims on May 13, 2017, 12:05:33 PM »
After a brief run through of previous parts i have purchased and compared to that of the stock motor, I have since discovered that the piston I installed is actually a 63mm rather than the 63.5mm piston that comes standard on the motor. Seems like the obvious smoking problem. I have purchased a 63.5mm piston and will install that and report back with any other issues if the same problem persists.
8
Chit Chat / Lifan smoke screen.
« Last post by BaileySims on May 12, 2017, 05:52:54 PM »
Hello all. Names bailey. I bought this lifan 200cc 163fml motor awhile back and have since been piecing it together to get it to run so i can build something to put it in. Since owning the motor, I have replaced the piston and rings, replaced the valves, valve seals, valve seats, valve springs and valve keepers. All the gaskets have been changes as well. I collected the electric parts to get it to run and wired it up correctly to do so. Here's the problem. Every time I start it, the first second, huge amounts of smoke start to come out of the exhaust. Oil is somehow finding its way into the combustion chamber and I cannot find out where or why. Have any of you ever had this problem and don't mind pointing me in the right direction? Thank you all.
9
LF400 / LF400, service manual, owners manual
« Last post by Cardillac on May 12, 2017, 12:55:33 PM »
Hello,

does anybody know, where i can find owners manual or service manual for Lifan 400 V-Twin?
10
LF125 / Lifan 125 9J Apollo, can't find a front Fender or break Pedal.
« Last post by YuJay on May 01, 2017, 04:00:09 PM »
Hey guys,

My first post and already demanding stuff. :)

I've been sending messages to every sale of a fender that looks like it would remotely looks like it would fit but all has been a dead end. :)
Would anyone happen to have a front fender compatible with the 9J?

I also need a foot brake pedal, but all the ones I see on eBay look different to what I need, mine looks like it curves out more.
Any help there?



Thanks for any advise or anyone who have these parts for sale!

EDIT: I'm also in the UK.
Pages: [1] 2 3 ... 10